Scule pentru masini de stantat tabla sistem Thick Turret si Trumpf - Mate Scule pentru abkanturi si cutite pentru ghilotine - UKB Prese configurabile si sisteme pentru imbinarea tablelor - TOX

UKB - scule speciale

Two-station hinge tools

Pentru orice detalii ne puteti contacta la:

Tel: +40 268 306 366 | Mob: +40 722 244 273
Email: office at langsin dot ro

Informatii generale

UKB poate executa la cerere orice tip de scule conform specificatiilor dvs. sau compatibile pentru realizarea pieselor dorite conform desenelor tehnice.

Acest link va deschide un tab nou, pentru revenirea pe pagina noastra va rugam sa reveniti pe tab-ul curent.

Catalog UKB - pdf

Formular contact


1 Punch top tool and die for an almost closed profile
2 Punch top tool and die with cut-out
3 Flattening tool with spring loaded die
4 Flattening tool with spring loaded die
5 Flattening tool with spring loaded die and retaining ledge
6 Flattening tool with spring loaded embossing-die and distance hemming unit
7 Flattening tool with spring loaded die and holding rail
8 Flattening tool with spring loaded die and back guide
9 Pre-bending and flattening tool for C-profile in 3 strokes
10 U-bending tool for C-profile in 2 strokes with spring loaded ejector
11 U-bending tool with bending strips and spring loaded ejector in the die and changeable blades at the punch top tool (working parts are exchangeable)
12 U-bending tools with PU-insert and counter pressure ledge and form punch-top tool
13 Top-hat bending tool with bending strips and
14 Top-hat bending tool with spring loaded ejector
15 Trapezoidal bending tool for direct located bends
16 Top-hat bending tool with spring loaded ejector
17 Large trapezoidal bending tool with spring loaded ejector
18 Large trapezoidal embossing-tool with anti-curvature
19 Special tool for radius bending at a very short flange
20 Radius tool with wings for overbending and spring loaded ejector
21 Radius tool for bending in PU-insert
22 Radius embossing-tool with wings for overbending
23 Radius embossing-tool with additional bending and back guide
24 Double radii embossing-tool
25 Large radius embossing-tool with straight run-out piece and cut-out
26 Large radius embossing-tool with extended flanges
27 Radius embossing-tool
28 Embossing-tool for a large radius with short straps
29 Embossing-tool with bending strips and spring loaded ejector
30 Joggle (Z) tool with adjustable bending strips in the die
31 Embossing-tool with adjustable strips at the punch-top tool
32 Embossing-tool for double joggle (Z) steps
33 Embossing tool for joggle (Z)-bending with different radii
34 Embossing-tool for multiple bending in one stroke
35 Embossing-tool
36 Embossing-tool
37 V-beading tool with spring loaded ejector
38 Beading tool with spring loaded ejector for contour bead
39 V-beading tool with a small radius embossing
40 Beading tool for round bead
41a Tool 1-2 Special joggle (Z) tool with cut-out for flanges
41b Tool 2-2 Flattening tool with back guide
42 Adjustable joggle (Z) tool with spring loaded ejector
43 Joggle (Z) tool for multiple bending
44 Joggle (Z) tool with additional flange bending
45 Special Joggle (Z) tool
46 Special joggle (Z) tool
47 Hinge tool

Pentru orice detalii ne puteti contacta la:

Tel: +40 268 306 366 | Mob: +40 722 244 273
Email: office at langsin dot ro


Pillar guided embossing-tool for embossing a 6°-bending, with large 3D-radius contour
Pillar guided bending tool for three beads with spring loaded ejector
Radius embossing-tool for embossing two lateral straps at the same time
Embossing-tool for displaced joggle (Z)-bending with springloaded hold-down devices, guide and locating bolt
Letters- and numbers embossing-tool with exchangeable stamps, height adjustable for coordination with other tool stations
Pillar guided nibble embossing-tool with spring loaded hold-down devices, cutting punches and cut-off bushings
Special tool for large joggle (Z)-bending with spring loaded hold-down device
Special tool for flattening of prefolded flanges by gate valves technology
Double radii embossing-tool with spring loaded ejector, lateral guided and mounting bold
Embossing-tool for three joggle (Z)-bending in onestroke with spring loaded ejector and mounting bold
Two-station tool for V-profile production Station 2 U-bending tool with spring loaded ejector
Two-station tool for case cover production Station 2 Radius tool with PU-insert for mark free bending of a 180° radius
Two-station tool for holder production Station 1 U-bending tool with back guide and spring loaded ejector
Two-station tool for holder production Station 2 V-embossing-tool with back guide, adjusted to the prior U-bending
Two-station tool for clamp production Station 1 Joggle (Z) embossing-tool for clamp shaping with spring loaded hold-down device and lateral support
Two-station tool for clamp production Station2 Tool for embossing a radius and roll into a clamp shape,with spring loaded hold-down devices&integrated support
Two-station tool for production of a holding plate Station 1 Embossing-tool for two 90° flanges with 3D-contour
Two-station tool for production of a holding plate Station 2 Bending tool for folding of two short straps at the already bended flanges with the help ofmovabl

Pentru orice detalii ne puteti contacta la:

Tel: +40 268 306 366 | Mob: +40 722 244 273
Email: office at langsin dot ro


Pentru orice detalii ne puteti contacta la:

Tel: +40 268 306 366 | Mob: +40 722 244 273
Email: office at langsin dot ro